Refine results by selecting a filter or click on 'All results' to search the whole site.
Skip to main content
RACELOGIC Support Centre

ADAS Test - Driver Status Monitoring, Long Distraction

  1. Last updated
  2. Save as PDF
This page contains an overview of the DSM Long Distraction test plugin in VBOX Test Suite.

The DSM: Long Distraction plugin for VBOX Test Suite gives you the ability to complete a Euro NCAP Driver Status Monitoring (DSM) / UNECE ADDW  test.

Ribbon - Test Setup

The DSM: Long Distraction has a unique Test Setup ribbon, from which you can configure the test.

VBTS_DSMLong_TestSetup.svg

Test Section

VBTS_DSMLong_TestSetup_TestSection.svg

Configure

Click on the Configure button to open the Settings window where you can define the parameters of the test.

Maths Channel

Click on the Maths Channels button to open the Maths Channels window to configure unique maths channels. You can find more information about maths channels in the Test Setup section.

Save Settings

Click on the Save Settings button to save the current test setup and add it to the Saved Settings area in the Add Test window.

The test will also be added to the list under the ADAS Test button on the Home tab for easy access.

Export

Click on the Export button to display a dropdown menu with the export options. You can export the selected results or line results to a .csv or a .txt file. 

Data Column Section 

VBTS_TestSetup_DataColumnSection.svg

Add

The Add button adds a column to the Test Results area. Click this button to open a dropdown menu where you can select a channel to display in the test results window.

Channel 

When you select a column header in the Test Results area, the channel name will be displayed in the Channel box (the top box in the Data Column section). Some columns will have required channels and cannot be changed, but if you can change the channel, the Channel box will become a drop-down list with the available channels.    

Data column_SelectedColumn_DefaultChannel.svg

Data column_SelectedColumn_EditChannel.svg
Result Condition

When you select a column header in the Test Results area, and it is a changeable channel, the Condition dropdown menu becomes available. The conditions will depend on the test and selected channel.

Examples are:

  • Avg
  • Max
  • Min
  • Delta 
  • At Start
  • At End
Sort Ascending

The Sort Ascending button will sort the values in the currently selected column in the Test Results area in alphabetical order from A to Z.

Sort Descending

The Sort Descending button will sort the values in the currently selected column in the Test Results area in alphabetical order from Z to A.

Run Section 

VBTS_TestSetup_RunSection.svg

Select All

Click on the Select All button to select every run in the Test Results area with one click.

Deselect All

Click on the Deselect All button to deselect every run in the Test Results area with one click.

Session Section
Edit Data 

VBTS_TestSetup_SessionSection.svg

Click on the Edit Data button to open the Session Data window and add various vehicle and test information, such as:

VBTS_DSMLong_SessionData.svg 

Vehicle Overlay

  • File
  • Colour
  • Length
  • Width
  • Antenna Placement
  • Advanced

Vehicle

  • Vehicle Model
  • Vehicle Number
  • Driver Name
  • Engine Model
  • Engine Number
  • Kerb Mass (kg)
  • Power (kW)

Wheels/Tyres

  • Front
    • Wheel
      • Dimensions
    • Tyres
      • Make
      • Dimensions
      • Model
      • Pressure (psi)
  • Rear
    • Wheel
      • Dimensions
    • Tyres
      • Make
      • Dimensions
      • Model
      • Pressure (psi)

Test

  • Test Date
  • Test Track
  • Test Facility
  • Comments

Conditions

  • Weather
  • Temperature (ºC)
  • Track Temperature (ºC)
  • Humidity (%)
  • Wind Speed (m/s)

When in Offline mode, the Session Data will be saved into the VBOX file.  This information will be recalled every time the file is loaded into VBOX Test Suite.

When in Online mode, a newly created session will be populated with session data from the previous session.

To save time, you can import and export the session data for other sessions. When you have completed the Session Data, you can export the data to a .vbses file by clicking on the Export button in the Session Data window. The exported file will contain all the session data and can be imported into another session via the Import button in the Session Data window.

Help Section 
Help

VBTS_TestSetup_HelpSection.svg

Click on Help to automatically open an Internet browser and load the relevant section of the User Guide on the Racelogic Support Centre.

Note: This page will only be displayed if there is a valid internet connection. If there is no valid internet connection, a cached version of the relevant section (from the last software update) will be presented in PDF form.

Test Settings

If you are creating a new test, the Settings window will open when you add the new test. This is where you can define the test parameters.

If you have already added a test and you have it open, you can click on the Configure button to open the Settings window to define or amend the test parameters.

VBTS_DSMLong_Settings.svg

Test Trigger Conditions
Start Trigger Channel

Click on the dropdown arrow and select the channel that will trigger the start of the test (or TGaze).  
 

A new test cannot be started until n seconds have elapsed

To avoid "false triggering", you can set the number of seconds you want to use as a buffer between tests.

 VBTS_DSMLong_Settings_TestTriggerConditions.svg
Channel Selections
Audible Warning Channel

Click the dropdown arrow to select the  channel for the Audible Warning signal.

This can be a digital trigger or a CAN message from a VBOX Audio Sensor or a third-party sensor signal sent over CAN.   
 

Audible warning trigger value

Set the value for when the audible warning trigger is deemed active.

Use the arrow buttons next to the value box to increase/decrease the value or type it directly into the box.  
 

Trigger when

This setting is a ‘True if’ function that denotes when the audible trigger is activated.

You can choose between the following:

  • Equal
  • Not Equal
  • Greater Than
  • Less Than
  • Greater Than or Equal
  • Less Than or Equal 
​​​​​​
​Fixed Audio Delay

The Audio sensor has a variable internal delay, introducing an unknown variable to the end-of-test time. To avoid variable delays, you can add a fixed delay to the output.  

Tick the Fixed Audio Delay box to enable a fixed delay and enter the required delay duration in the value box that appears to the right of the setting when it is enabled. 
 

Visual Warning Channel

Click the dropdown arrow to select the channel you want to use for the visual warning signal.

This can be a digital trigger from a VBOX Audio Sensor or a third-party sensor signal sent over CAN.   
 

Visual warning trigger value

Set the trigger value for when the visual warning trigger is deemed active. 

Use the arrow buttons next to the value box to increase/decrease the value or type it directly into the box.
 

Trigger when

This setting is a 'True if’ function that denotes when the visual trigger is activated.

You can choose between the following:

  • Equal
  • Not Equal
  • Greater Than
  • Less Than
  • Greater Than or Equal
  • Less Than or Equal 
 VBTS_DSMLong_Settings_ChannelSelections.svg
Pass Conditions
Seconds from t-Gaze to warning (t_Warn)

Set the pass condition for the number of seconds from the t-Gaze to the warning depending on the protocol requirements.  

Use the arrow buttons next to the value box to increase/decrease the value or type it directly into the box.
 

Test ends after seconds from t-Gaze

Set the pass condition for the seconds between the t-Gaze (Start Trigger) and the End of Test (EoT). 

Use the arrow buttons next to the value box to increase/decrease the value or type it directly into the box.

 VBTS_DSMLong_Settings_PassConditions.svg

Ribbon - Chart

The DSM: Long Distraction has a unique section on the Graph ribbon, in which you can find some plugin-specific tools.

VBTS_DSMLong_Ribbon_Chart.svg

Event

VBTS_DSMLong_Ribbon_Chart_Event.svg

Add t-Gaze

Add a t-Gaze event to the test by clicking on the Add t-Gaze button with the cursor at the required location in the chart. 

Selected Event

When you have added one or more t-Gaze events to the test, the selected event will be displayed. Click on the dropdown arrow next to the event name to see the available events in the test and select a different one. 

Rename

You can rename the events in the test. Select the required event and click Rename. 

Delete

You can delete events from the test. Select the required event and click Delete. 

Seek t-Gaze

When you have added t-Gaze events to the test, you can use the Seek t-Gaze feature to move to different locations in the graph. 

VBTS_DSMLong_Ribbon_Chart_Seek-t-Gaze.svg

t-Gaze

Click the t-Gaze button to move the cursor to the nearest t-Gaze event in the graph. 

-0.16s

Click the -0.16s button to move the cursor to 0.16 seconds before the t-Gaze event (Lizard). 

-0.48s

Click the -0.48s button to move the cursor to 0.48 seconds before the t-Gaze event (Owl). 

-1.00s

Click the -1.00s button to move the cursor to 1.00 seconds before the t-Gaze event (One Second). 

-4.00s

Click the -4.00s button to move the cursor to 4.00 seconds before the t-Gaze event (Four Seconds). 

Test Results Area

The Test Results area displays instantaneous results from the current test session. In this area, you can review test-specific criteria such as the duration from test start to Visual / Audio warning as well as the overall PASS/FAIL result.

You can review the live results and assign any edge cases to be considered for further review offline.

Every time you start a new test (via the START button on the dashboard), VBOX Test Suite will add a new tab to the Test Results area. This gives you the ability to switch between separate tests (for example different Gaze locations). You can remove a session from the Test Results area by clicking the X icon on the tab.

Rename File

You can rename a session tab by double-clicking the tab header. Changing the name on the session tab in the software will automatically change the name of the locally saved VBOX file (.vbo or .vbb).

Edit Session Data

By pressing the Edit Data button next to the name of the session in the Test Results area or on the Test Setup tab on the ribbon, you can add vehicle and test information to the session.

  • When in Offline mode, this information will be saved into the VBOX file, meaning that this information will be recalled every time the file is loaded into VBOX Test Suite.
  • When in Online mode, a newly created session will be populated with session data from the previous session.

This information will be included in the test report to make it easier to see under what conditions the test was conducted.

To save time, you can import and export the session information for use in other sessions (the entire range of data is exported, not just the visible screen).

Once the session information has been completed, you can export the data to a .vbses file. This file will contain all the session information that can then be imported into the open session information field.

Note: This data is purely optional and has no effect on the test or the test results. 

 

Result Columns

VBTS_DSMLong_Results.svg
 

The Test Results area has the following default columns:

Run Indicates which run number the results relate to, with run one being the first run completed.

There is also a selection box that, when ticked, includes that run in the graph and into the Average/Max/Min/Standard Deviation calculations. Once selected, a coloured square will appear to indicate which colour this run is displayed as on the graph.
 
Note: If you are loading a file in Offline mode, all valid runs will automatically be ticked.
Duration (s) The total duration of the test, from Taway (manual trigger) to Twarn (audio or visual warning). 
Audible (s)

The time in seconds from the start of the test (Taway) to the audible warning (if one is given).

If no audible warning is given or if the visual warning is given before the audible warning, the result will display as 0.00. 
Visual (s)

The time in seconds from the start of the test (Taway) to the visual warning (if one is given).

If no visual warning is given or if the audible warning is given before the visual warning, the result will display as 0.00. 
Pass/Fail Overall Pass/Fail result of the run based on the duration from manual trigger to warning activation.
  1. Back to top
  • Was this article helpful?

Recommended articles

  1. Article type
    Reference
    Audience
    Public
  2. Tags
    This page has no tags.