Skip to main content
RACELOGIC Support Centre

01 Getting Started – VBOX Touch RTK


Please register your VBOX Touch RTK so that Racelogic can continue to provide you with notifications about the latest software releases and firmware upgrades for your Racelogic product, and offer technical support.

Register your device here.


What is in the box? 

When you purchase a VBOX Touch RTK (RLVBTOUCHR), you will find the following items when you open the box:

Product Code Quantity Description
MECH0298SD 1 Rubber Overmould for VTS – Black
RLCAB010LE 1 Cigar Plug Power Supply (RLVBTOUCH, 2 m)
RLACS313 1 8 GB SD Ultima Pro UHS-1 Memory Card
RLACS308 1 GPS L1/L2, GLONASS G1/G2/G3, Galileo E1/E5b, and BeiDou B1/B2 GNSS Antenna cable with SMA connector (3 m)
ACS318MOUNT 1 Swivel Neck Richter Suction Mount
RLACS281 1 Plastic Carry Case for VBOX Touch
RLCALUKAS 1 Certificate of Calibration


Optional Accessories

Product Code Description
RLVBACS004 Brake Pedal Trigger
RLVBACS010 Hand Held Start/Stop Logging Switch
RLCAB001 VBOX PC Serial Cable

SD Card

VBOX Touch logs data to an SD card. Depending on the Logging Strategy that is set in the General Settings area, the unit will either log continuously or when movement is detected (default). You can find more information on this here.

SD Card Format

VBOX Touch is supplied with an 8 GB SDHC card in a FAT32 file format, which is the only file format supported.

If you are looking to purchase a new SD card, it is recommended that any card used has a write speed of above 7 MB/s (4 MB/s absolute minimum) and a speed class of 10 (4 absolute minimum). Racelogic recommends SD cards from quality brands such as Transcend, SanDisk, Kingston or Lexar to ensure the best results.

If an SD card is formatted in the exFAT or NTFS file formats, it will need to be reformatted into a FAT32 file system before it will work with a VBOX Touch unit.

SDHC cards (2 GB to 32 GB)

Supplied or purchased SDHC cards are formatted in the FAT32 file format. This format is supported by VBOX Touch.

SDXC cards (64 GB and above)

Purchased SDXC cards will be formatted in exFAT or NTFS file formats; these formats are not supported by VBOX Touch (please reformat as per instructions below).

SD Card Reformatting

  • FAT32 reformatting for media with sizes up to 32 GB can be done directly within Windows by right-clicking on the media and selecting 'Format'.
  • If you would like to format media with sizes above 32 GB into a FAT32 file system, this isn't something that can be done directly within Windows as it is not the standard formatting for the file. However, many third-party software programs can be used to reformat media to allow them to work correctly with our products - we can recommend  This Tool as a free option from the SD card organisation.

The VBOX Touch RTK unit can be powered by the supplied RLCAB010LE cable connected to a vehicle's 12 V cigar power socket. 

On boot up, the VBOX Touch will display a splash screen and automatically look for satellites and media.

VBOX Touch Splash.png

The first time that the unit is booted up, the Display Mode screen will be presented. Every time after this, the last used display mode will be opened.


VBOX Touch logs data via an SD card inserted into the Side of the Unit. Dependent on the Logging Strategy selected within the General Settings area, the unit will either log continuously or when movement is detected (default).

Tapping on the SD Card Icon when green will manually start or stop logging data, overriding the Configured Logging Strategy.

The Record Icon will show when the unit is logging data to the SD card.

If you have come to a stop, but the Record Icon is still on, press the SD Card Icon to stop the logging before removing the card.

Sometimes, due to poor satellite visibility in a garage or close to a building, the box may start recording, even if the car is stationary. Always check the Record Icon before ejecting the card.

Do not remove the SD card when the Record Icon is on as you may lose data.

Note: If for some reason the SD card is removed while the unit is still recording, it may need to be repaired using a PC before it can be reused.

Logging Switch

You can also control the logging by using an RLVBACS010 hand-held latching trigger switch (unlatched for logging/ latched for not logging). Continuous Logging Mode should be selected when using the switch. It is connected to the 3-pin Digital In and PPS Connector on the side of the VBOX Touch.

When the trigger switch is connected and latched, it is not possible to use the SD Card Icon to manually start or stop logging data.

Logged Channels

VBOX Touch logs channels to an inserted SD card within a .vbo file, channel information is available below:

  • Satellites: This is the number of satellites in use.
  • Time: This is UTC since midnight in the form HHMMSS.SS.
  • Latitude: Latitude in minutes MMMM.MMMMMMMM +ve = North e.g. 3169.30644410M = 52D, 49M, 18.4S.
  • Longitude: Longitude in minutes MMMMM.MMMMMMMM +ve = West e.g. 00040.18164742M = 00D, 40M, 10.9S.
  • Velocity: Velocity in km/h.
  • Heading: Heading in degrees concerning North.
  • Height: Height above sea level in meters based on the model of the earth used by VBOX GNSS engines.
  • Vertical velocity: Vertical velocity in km/h. +ve velocity uphill, -ve velocity downhill.
  • Long accel: Longitudinal acceleration in g, +ve for forward acceleration.
  • Lat accel: Lateral acceleration in g, +ve for acceleration to the left.
  • Solution type: Indicator for what the unit is currently using to derive position: 0 = No sats; 1 = Standalone using GNSS only; 2 = DGNSS; 3 = RTK Float (RTK but not full resolution); 4 = RTK Fixed.
  • Event 1 time: This is the digital input oversample timer used to interpolate the trigger event time between captured samples.
  • Correction age (VBOX Touch RTK only): RTK signal age in seconds, if there is a loss in connection, the value resets at 60 s.
  • GPS Sats Used (VBOX Touch RTK only): Number of GPS satellites in use.
  • Glonass Sats Used (VBOX Touch RTK only): Number of Glonass satellites in use if selected within the GNSS Selection area within the General Settings menu.
  • Beidou Sats Used (VBOX Touch RTK only): Number of Beidou satellites in use if selected within the GNSS Selection area within the General Settings menu.
  • Galileo Sats Used (VBOX Touch RTK only): Number of Galileo satellites in use.

You can find more information about the VBO file format here.

  • Was this article helpful?