Skip to main content
RACELOGIC Support Centre

Speed Display Mode - VBOX Touch (v2/v3)

The Speed Display Mode allows you to view live speed data. You have 3 screen options; Speed, VMAX and Average Speed. You access the speed menu by pressing the Mode button at the bottom of the screen and selecting Speed.
The last selected Speed Display Mode will be displayed after each power cycle.

Speed Display Mode Overview

There are 3 different Speed Display screens that you can move between by using the Forward and Back arrows at the bottom of the screen or by swiping left or right.


Speed Display - Speed Screen

This is the default speed screen and it displays live speed data. If you have selected a Target Speed in the Speed Settings, it will be displayed in grey underneath the live speed.
VBOX Touch Speed Screen_600px.png
If the vehicle is travelling slower than 0.5 km/h or if VBOX Touch has lost its satellite lock (less than 4 satellites), the speed value will be 000.0.

Speed Display - VMAX Screen

This screen displays the absolute top speed reached until you press the Reset button at the bottom of the screen.

If you have set a Target Speed in the Speed Settings, it will be displayed in grey underneath the VMAX value.

VBOX Touch Speed2 small_600px.png

Speed Display Settings

You can access the Speed Display settings by pressing the Settings button at the bottom left of the screen and selecting Speed
VBOX TOUCH FW v1.5 - Speed Settings (TS 20OCT2022)_600px.png
To return to the main screen, press the Exit button at the bottom left.

Decimal Places

VBOX Touch Speed Settings Decimals.png
You can adjust the number of decimal places displayed for speed values across all the Speed displays. You can choose between 0, 1 (default) and 2 decimal places. Tap the button to cycle through the options.

Speed Display Smoothing

VBOX Touch Speed Settings Smoothing.png
If required, the live speed values displayed can be smoothed. Your options are 0.0 s, 0.25 s (default), 0.5 s and 1.0 s. These time values refer to the amount of time that the displayed data is averaged by. Tap the buttons to change the smoothing levels.
This option will smooth live speed displays in all relevant screen modes.


  • Smoothing only applies to the screen displays, not the recorded data.
  • Smoothing introduces a slight delay to the displayed value.

V Avg Mode

VBOX Touch Speed Settings Average.png

You can change whether the average speed on the Average Speed Screen is calculated as Continuous or Moving.

  • Continuous: Average speed will start to calculate as soon as an SD card is inserted and initialised.
  • Moving: Average speed will start to calculate as soon as VBOX Touch detects a speed over 0.8 km/h. Calculations will stop when the speed is under 0.8 km/h.

Distance Display

VBOX TOUCH FW v1.5 - Speed Settings (TS 20OCT2022)_Distance-display.png

This setting lets you change the unit used for the distance travelled when you are using the Average/Distance screen. The Distance Display setting will toggle between Feet/Miles (if the Distance unit is set to feet in the General Settings) or will toggle between Metres/Kilometres (if the Distance unit is set to metres in the General Settings)

Set a Target Speed

VBOX Touch Speed Settings Target.png

You can define a target speed that will be displayed underneath the speed value on the speed screens.

You can choose whether to enable or disable an audible alert (continuous beep for 2 seconds) along with a visual alert (all 4 LEDs will flash green) when you reach the target speed. Alerts will only show once unless the vehicle has been stationary since the last alert.

Enabling one, or both, of the alerts will set the target speed and also allow you to access the sub-menu where you can define the target speed condition by pressing the target sped value and then using the presented keypad.

Input Target Speed (100) - No Frame_600px.png
Target Speed Keypad Example

To save the value inputted, press the Confirm Button on the bottom right of the screen, or press the Cancel Button on the bottom left of the screen to return the Settings screen without saving. The value will be remembered after each power cycle.

Note: Speed can be entered up to 1 decimal place.


Selecting the Reset button at the bottom right of the screen will reset all results shown on the current screen. When pressed, the LEDs will briefly flash green twice.



  • Was this article helpful?